• Türkçe
    • English
  • Türkçe 
    • Türkçe
    • English
  • Giriş
Öğe Göster 
  •   DSpace@Amasya
  • Araştırma Çıktıları | TR-Dizin | WoS | Scopus | PubMed
  • WoS İndeksli Yayınlar Koleksiyonu
  • Öğe Göster
  •   DSpace@Amasya
  • Araştırma Çıktıları | TR-Dizin | WoS | Scopus | PubMed
  • WoS İndeksli Yayınlar Koleksiyonu
  • Öğe Göster
JavaScript is disabled for your browser. Some features of this site may not work without it.

Experimental and statistical investigation of the machining performance of wave form end mills on AISI 316L stainless steel

Erişim

info:eu-repo/semantics/openAccess

Tarih

2021

Yazar

Aydin, Kutay
Katmer, Sukran
Gok, Arif
Seker, Ulvi

Üst veri

Tüm öğe kaydını göster

Özet

Wave form end mills with variable rake and helix angles are new in the machining industry, and limited information is available on their machining performance. In this study, the machining performance of wave form end mills with variable rake and helix angles on the helical cutting edge on AISI 316L austenitic stainless steel which is in the difficult-to-cut materials due to work hardening, high tool wear and build-up edge (BUE) was investigated. In this context, five different carbide cutting tools, which are wave form tools with different wavelengths (mm) and wave amplitudes (mu m) (6-550, 8-250, 4-450, and 8-650) and the standard tool, were evaluated through both experimental and statistical approaches in consideration of cutting forces, surface quality, tool life criteria. In terms of cutting forces and surface quality; wave form tools exhibited higher cutting forces and surface roughness values than the standard tool in all machining conditions, due to the predominance of machining negativity in negative rake angle regions despite the advantages provided by the positive rake angle regions. On the other hand, in 8-250 and 8-650 waveform tools with smaller positive and negative rake angles (+4 degrees, -2 degrees, -3 degrees) were observed low tool wear values 17.2% and 6.9%, respectively compared to the standard tool. As a result, it is thought that 8-250 and 8-650 wave form tools can be a solution in rough milling processes for the low tool life problem caused by high mechanical strength and high work hardening properties that make difficult-to-cut AISI 316L material.

Cilt

36

Sayı

4

Bağlantı

https://doi.org/10.17341/gazimmfd.881590
https://search.trdizin.gov.tr/yayin/detay/494877
https://hdl.handle.net/20.500.12450/2532

Koleksiyonlar

  • Scopus İndeksli Yayınlar Koleksiyonu [1574]
  • TR-Dizin İndeksli Yayınlar Koleksiyonu [1323]
  • WoS İndeksli Yayınlar Koleksiyonu [2182]



DSpace software copyright © 2002-2015  DuraSpace
İletişim | Geri Bildirim
Theme by 
@mire NV
 

 




| Yönerge | Rehber | İletişim |

DSpace@Amasya

by OpenAIRE
Gelişmiş Arama

sherpa/romeo

Göz at

Tüm DSpaceBölümler & KoleksiyonlarTarihe GöreYazara GöreBaşlığa GöreKonuya GöreTüre GöreBölüme GöreYayıncıya GöreKategoriye GöreDile GöreErişim ŞekliBu KoleksiyonTarihe GöreYazara GöreBaşlığa GöreKonuya GöreTüre GöreBölüme GöreYayıncıya GöreKategoriye GöreDile GöreErişim Şekli

Hesabım

GirişKayıt

DSpace software copyright © 2002-2015  DuraSpace
İletişim | Geri Bildirim
Theme by 
@mire NV
 

 


|| Yönerge || Rehber || Kütüphane || Amasya Üniversitesi || OAI-PMH ||

Amasya Üniversitesi Kütüphane ve Dokümantasyon Daire Başkanlığı, Amasya, Turkey
İçerikte herhangi bir hata görürseniz, lütfen bildiriniz: openaccess@amasya.edu.tr

Creative Commons License
DSpace@Amasya by Amasya University Institutional Repository is licensed under a Creative Commons Attribution-NonCommercial-NoDerivs 4.0 Unported License..

DSpace@Amasya: