Basit öğe kaydını göster

dc.contributor.authorGok, Kadir
dc.contributor.authorSari, Huseyin
dc.contributor.authorGok, Arif
dc.contributor.authorNeseli, Suleyman
dc.contributor.authorTurkes, Erol
dc.contributor.authorYaldiz, Suleyman
dc.date.accessioned2019-09-01T13:04:43Z
dc.date.available2019-09-01T13:04:43Z
dc.date.issued2017
dc.identifier.issn0954-4089
dc.identifier.issn2041-3009
dc.identifier.urihttps://dx.doi.org/10.1177/0954408915576698
dc.identifier.urihttps://hdl.handle.net/20.500.12450/1063
dc.descriptionWOS: 000396206300003en_US
dc.description.abstractIn this study, milling operations were carried out using AISI 1040 specimens steel in dry cutting conditions. The cutting tools used in the experiment include P20 tool steel and they also have three different approach angles (45 degrees, 60 degrees, 75 degrees) and rake angles (0 degrees, -6 degrees, -12 degrees). In milling experiments, cutting parameters with a depth of cut of 1.5mm, cutting speed of 193m/min, and feed rate of 313mm/min were selected. A comparison was presented between the force values which were obtained by measured value and predicted with numerical simulations, and then a good agreement was found between measured and predicted force values. As result of, it was observed that the rake and approach angles were effective in milling operations.en_US
dc.description.sponsorshipSelcuk University Scientific Research Project Department [06101047]en_US
dc.description.sponsorshipThe author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: The experimental part of this study was supported by the Selcuk University Scientific Research Project Department under the project number of 06101047.en_US
dc.language.isoengen_US
dc.publisherSAGE PUBLICATIONS LTDen_US
dc.relation.isversionof10.1177/0954408915576698en_US
dc.rightsinfo:eu-repo/semantics/closedAccessen_US
dc.subjectMetal cuttingen_US
dc.subjectfinite element methoden_US
dc.subjectmilling operationsen_US
dc.subjectrake angleen_US
dc.subjectapproach angleen_US
dc.titleThree-dimensional finite element modeling of effect on the cutting forces of rake angle and approach angle in millingen_US
dc.typearticleen_US
dc.relation.journalPROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART E-JOURNAL OF PROCESS MECHANICAL ENGINEERINGen_US
dc.identifier.volume231en_US
dc.identifier.issue2en_US
dc.identifier.startpage83en_US
dc.identifier.endpage88en_US
dc.relation.publicationcategoryMakale - Uluslararası Hakemli Dergi - Kurum Öğretim Elemanıen_US
dc.contributor.department-temp[Gok, Kadir] Dumlupinar Univ, Kutahya Vocat Sch Tech Sci, Germiyan Campus, TR-43100 Kutahya, Turkey -- [Sari, Huseyin] Selcuk Univ, Ilgin Vocat Sch Tech Sci, Ilgin, Konya, Turkey -- [Gok, Arif] Amasya Univ, Dept Mech Engn, Fac Technol, Amasya, Turkey -- [Neseli, Suleyman -- Yaldiz, Suleyman] Selcuk Univ, Dept Mech Engn, Fac Technol, Konya, Turkey -- [Turkes, Erol] Kirklareli Univ, Dept Mechatron Engn, Fac Technol, Kirklareli, Turkeyen_US


Bu öğenin dosyaları:

DosyalarBoyutBiçimGöster

Bu öğe ile ilişkili dosya yok.

Bu öğe aşağıdaki koleksiyon(lar)da görünmektedir.

Basit öğe kaydını göster